Adding terpenes to cbd isolate
The following information is just a guide and so you should expect to experiment a little bit to find the sweet spot for you.
With that said, lets begin.
Firstly a few things you that might help you along the way.
if using plastic cartridges it is not advisable to go over 6% terpene content as it can, but not always, have a negative reaction and in some cases impart a burnt taste. Poor quality plastic cartridges will require another product to dissolve your extract. Use our fractionated coconut oil for best results. Fr actionated coconut oil can also be used as a diluted for those who prefer to use lower doses of cannabinoids in there vape pens or as a means of dissolving wax extracts and preventing them from going cloudy.
Starting Material Percent by weight Notes
shatter/oil/pull and snap 5-10% No need to use fractionated coconut oil but you can if you prefer a lower dose cart
Wax/Rosin 5-10% Remember to use fractionated coconut oil to dissolve waxes
Distillate 10-20% Remember distillate will always oxidise and some terpenes may affect colour
Flowers/Buds 2% Recommend applying 1 small drop onto bud just prior to grinding
Champagne/Beverages 5 drops/litre 1 drop per glass of champagne
Edibles 1% Terpenes can overpower edibles so go sparingly
CBD crystal (isolate) 2% Approximately 1 drop from dropper per gram.
Cosmetics 5% Add as late in the process as possible for best results
The first thing you should consider when mixing your own vape cartridges is your starting material .
When mixing with cannabinoids like CBD,CBG and others it all about the starting consistency. There are lots of different types and so below we have created a guide for each type you are most likely to encounter.
When mixing with SHATTER or DISTILLATE (ie any winterised oil)
Start by placing your starting material into a glass jar. Always use glass as it is non reactive and may be heated.
For a single cart start with 0.4g.
Add the terpene profile of your choice to the required dose. Either use the table above or stick with 1-2 drops per gram of oil. Remember if going free style like this then start small, as you can always add more but cant take it away once added.
Put the lid on your mixing vial and lower into a coffee mug of hot water straight from the kettle. Leave it like this for 1 to 2 minutes.
Remove from mug and stir. Using a clean dabber is fine. If its not quite coming together as a smooth consistency then you might want to reheat for a litlle longer
Put finished mix in fridge for 5 minutes to help bring back down to room temperature. Check your consistency is good and load into pen with syringe. Sometimes it helps to reheat mix to make loading into cart easier before cooling again. This is normal practice when handling high viscosity oils for use in the thick oil carts.
When mixing with CBD isolate
When mixing terpenes with CBD isolate we have found the desirable starting range to be 2-5% by weight.. This equates to 1-2 drops from one of our droppers onto 1g pure CBD crystal. Some have said that they prefer 10% but this is far too strong for me. Be prepared to leave the lid on and refrain from trying it overnight for best results.
When Mixing with WAX/Rosin/CO2
The process is exactly the same as with winterised oils only it is important to add fractionated coconut oil to the mix as well to prevent any waxes from separating over time and giving your oil a cloudy appearance. 1-2 drops per gram should be sufficient. Note, fractionated coconut oil can also be used as a diluted for those who prefer to use lower doses of cannabinoids in there vape pens.
Find out all you need to know about terpenes and how to use our products. Use in vape juices, dab with it or drop on your flowers.
What is CBD Isolate & How is it Used?
As the name suggests, CBD isolate is a pure isolated form of cannabidiol – a primary, non-psychoactive cannabinoid found in cannabis.
CBD isolate is sourced from hemp using extraction and processing methods to isolate the molecule into a white crystalline powder. This powder is free of all other cannabis plant materials including the high-inducing cannabinoid THC. Isolate can be used as a standalone product or as an ingredient in common CBD formulations.
In this article, we provide all the essential information you need to know about CBD isolate including how it’s made, how it’s used, and the limitations of this substance compared to other types of hemp extracts.
How is CBD Isolate Made?
The appearance may make you think that CBD isolate is produced synthetically in a lab, but it is not. Like any other CBD-rich extract, isolate begins its life in plant form. Isolate can be sourced from either marijuana or hemp, though products publicly available for sale are exclusively derived from hemp. This is because hemp is bred to contain high levels of CBD and trace amounts of THC (the opposite chemical profile of most marijuana) to stay within the federal legal limit of 0.3% THC by dry weight.
The process to make isolate begins with hemp plant material which undergoes extraction resulting in a thick oily substance. This extract is known as full-spectrum because it contains a whole-plant chemical profile that mirrors that of the original plant source. The compounds found in this oil include cannabinoids, terpenes, flavonoids, chlorophyll, fatty acids, and more.
To isolate the cannabidiol, further processing of this whole-plant extract is performed. Filtering removes the excess plant compounds before the CBD is separated from the other cannabinoids and terpenes through distillation. The result is a crystalline substance containing up to 99% pure CBD.
After the isolate is created, it should be screened at a lab, testing for potency and purity. High-quality companies will provide these lab reports to the end consumer to verify the purity and concentration of the final product. For more information on how to identify isolate-based products by their lab reports, see our guide.
Types of CBD Isolate
The versatility of CBD isolate is one of the most attractive things about it. As a consumer, you’ll find a wide range of products from pure isolate sold alone, to a wide variety of products crafted with isolate as the main ingredient:
When CBD is isolated from a full spectrum extract, the end result is a thin white slab. This slab is commonly pulverized into a powder, but sometimes it is sold as a single slab or in small pieces. There is no chemical difference between a slab and powder. Slab isolate is often sold simply because it is easier to use when vaping or dabbing.
Crystals / Powder
Most commonly, you’ll find CBD sold as a white powder. This powder is created by pulverizing a slab of isolate into a fine dust. This powder can be used in a variety of ways including used directly or as an ingredient in other finished products.
Using CBD isolate as an ingredient to create end products is a common practice. You’ll find isolate-based products of nearly every type available on the market today including capsules, tinctures, balms, vape products, and more.
Since all the terpenes and cannabinoids are removed when making CBD isolate, some companies will add hemp or marijuana-derived terpenes back into an isolate. The result is an enjoyable, aromatic product that provides additional therapeutic benefits via the terpenes. Most commonly this is done on products designed to be dabbed/vaped.
CBD Isolate vs Full/Broad-Spectrum: Effectiveness & the Entourage Effect
The supporting cannabinoids and terpenes found in full and broad-spectrum extracts have been researched individually to provide many unique benefits. These compounds are also known to offer synergistic benefits when consumed together, something known in the cannabis industry as the entourage effect.
Because CBD isolate is missing these supporting compounds, this sacrifices some therapeutic benefits that a whole plant approach offers. A 2015 research document highlighted the need for higher, more precise isolate dosing to achieve the desired effects when compared to full-spectrum extracts. Cannabinoid and terpene-rich whole plant alternatives were shown to be more effective at lower dosing.
For those drawn to CBD isolate due to it’s lack of THC, broad-spectrum product offers a full-spectrum profile with only the THC removed. These products retain the maximum possible levels of beneficial cannabis compounds without THC exposure, making them a great alternative to CBD isolate.
If you’re interested, be sure to browse our selection of broad-spectrum options right here at Big Sky Botanicals!
How to Use CBD Isolate
Despite CBD isolate’s inability to produce the entourage effect, the molecule still has plenty of research-backed and anecdotal evidence supporting its effectiveness. The isolate form also has some distinct advantages that make it attractive to new and experienced users. Namely, an isolate is THC-free, low cost, and extremely versatile. Below we highlight the many ways you can use CBD isolate:
Make Your Own CBD Tincture
You can easily save some money by using isolate to create your own tinctures as opposed to buying them pre-made. In addition to getting more bang for your buck you also get control over the carrier oil, potency, and any flavoring additives.
Before you start, you’ll need a dropper bottle. Most commonly you’ll find tinctures in 30 ml (1 oz) or 15 ml (1/2 oz) dropper bottles. You can find these online for as little as $1 each or head down to your local health food or supplement store for comparable products.
Once you’ve secured your dropper bottle, its time to whip together your tincture. The two key components are simple: CBD isolate and a carrier oil. The most common carrier oils are MCT oil or hemp seed oil. Again, both of these can be purchased at your local health food store or online. Once you have your ingredients, all there is left to do is decide on a concentration, mix them up and you’re off to the races.
Hot Tip: crystalline CBD will mix into a carrier substance more quickly if heated. Continue adding heat and mixing until the cloudiness (undissolved CBD crystals) disappears, pre-heating the fatty substance to 175°F-200°F (80°C-93°C) before mixing is ideal. Once fully emulsified, keep in the refrigerator to keep it from re-crystallizing.
Add it to Edibles & Foods
All cannabinoids, including CBD, are fat-soluble. This means they mix into fatty substances like oil. You can easily add isolate into many types of edible food products containing ingredients like butter, coconut milk, or cooking oil. You can also use the CBD as a ‘seasoning’ and sprinkle it on top of nearly anything. The options here are basically endless, so here are a few ideas to get you going:
- Cookies, Brownies, Gummies, & Candies
- Salad Dressing
- Dog/Cat Treats
- Bulletproof Coffee
But Not to Drinks.
The CBD molecule is hydrophobic, meaning it does not dissolve into water. Because of this, isolate added to water will not dissolve. This means adding isolate to drinks is a no-go unless that drink contains a small amount of oil already.
There are some recent technological advances that have enabled manufacturers to create powder and liquid-form emulsified CBD which will disperse into water. We’ve taken advantage of this technology and now carry a water-soluble tincture that can be added to liquids!
Make Your Own CBD Capsules
If you followed the steps above to make a tincture, then making CBD capsules is a breeze. Capsules and tinctures often have the same ingredients, with just the concentration likely adjusted due to the small amount of liquid that a capsule holds. MCT oil is a great carrier oil for anything CBD-based that you’ll be swallowing.
To make capsules all you’ll need are some veggie caps. Again, these can be found at your local health food store or online. Pop open the capsules and fill them with your CBD/oil mixture and pop it back together. A commonly used concentration is 10-25mg of CBD per capsule.
Make Your Own Topicals
Isolate is great as an ingredient in topicals like salves and creams. You can follow one of the many online tutorials starting from scratch and make your own topical or add CBD to an existing oil-based product.
Add CBD to Your Vape Juice
This one is very straightforward, just add isolate to an existing vape juice. You get to choose how much to add and control the overall potency. This is a great option for existing e-cigarette users looking to begin vaping CBD.
Smoke CBD Isolate in Your Dab Rig or Wax Pen
Dabbing or vape-dabbing CBD isolate is a very common use for the substance and one that comes with a wealth of positive anecdotal feedback. Simply add a small amount of isolate to your dab rig or wax pen and hit it as you would normally. This method of ingesting CBD is highly bioavailable and has a quick onset time. This allows you to feel immediate relief.
If you’re looking for more information about dabbing, we’ve put together a guide specific to CBD users.
Create Your Own Terpsolate
A terpsolate is a combination of CBD isolate and a liquid terpene extraction. Terpenes add an additional dimension to the dabbing or vaping experience. When adding terpenes to an isolate you end up with a partial entourage effect. Terpenes can add an uplifting, positive, and energizing or sedating, relaxing, and calming tone to your isolate.
To make a terpsolate, simply add small amounts of liquid terp extract to your isolate and stir. Be careful not to add too much and go too runny. Ideally, you still want a fairly viscous consistency so you can easily manipulate the terpsolate into your dab rig or wax vape pen.
Sprinkle on Top of Smoked or Vaped Marijuana
This last one is for recreational or medical marijuana users. You can sprinkle some CBD on top of your flower when smoking or vaping herb. The added CBD is known to ‘smooth out’ the THC-induced high. CBD is known to counteract the harsher psychoactive side of THC and produce a more enjoyable high – in addition to the added therapeutic benefits of higher CBD concentration.
Will CBD Isolate Show Up on a Drug Test?
Common drug tests looking for marijuana use tests for the presence of the metabolite THC-COOH, the resulting molecule present in the body after THC is consumed. Since CBD isolate is stripped of all other cannabis compounds, the end product is THC free. This means CBD isolate would not result in the failure of a drug test looking for THC use.
We dive more into this concept in our article which covers CBD and drug testing. You should always verify that the product your taking is free of THC by verifying lab reports, regardless of what the marketing copy says.
The THC-free nature of CBD isolate was long an attractive draw for those looking to benefit from the use of a CBD product. Luckily new advances in extraction and processing have created a new spectrum of products that preserves the full spectrum effectiveness with the THC-free accessibility of isolate.
Save 20% For Life
Unlock an increasing lifetime discount with the Charter Buyer Club.
Shop with us and automatically earn discounts on future orders – up to 20% off, for life!
9 comments on “ What is CBD Isolate & How is it Used? ”
Exceptional Article! I think the best described article for the CBD Isolate. It is step by step so I get all answers to my questions and is very informative at the same time.
How do you use CBD slab? Can I ingest? Place under the tongue?
Hi Heather, the only difference between CBD slab and powder is that the powder is slab isolate that’s been crushed down into a powder. That said, you can use them in exactly the same ways. Perhaps the only unique thing about slab is it’s easier to grab chunks of it for uses like dabbing – otherwise they are interchangeable.
I was wondering if I could use CBD isolate slabs on a wax vape.
Hi Carly, yes, this should work fine!
I was hoping to find mixture recipes for us who are challenged with the ml/mg/g/mg ranges.
I want to mix one cup of carrier oil with 1 g of 99% pure isolate. What potency will I get?
Hey David –
It sounds like you’re making your own tincture or capsules and could use a little pre-planning before you star mixing. To target the right potency, you need to determine your serving size and desired MG of CBD. To use a common example, a 30ml tincture contains thirty, one ml servings. If you were to add 300mg of isolate and the remaining volume with the carrier oil you’d have 10mg of CBD per serving. 600mg of CBD with the carrier oil would give you 20mg per serving etc.
Good evening. Curious to understand – if a hemp plant as a CBD content of 10% – would that mean 10% of its biomass would convert to isolate? i.e. 10kgs of plant would equal 1kg of isolate? Thanks!
Hey Oli – wish I could have a good answer for you, but we can’t speak accurately to this question simply because we don’t extract plant material ourselves. I’d wager to guess that it’s not this straightforward, but you’d need to talk to someone working in the extraction industry for a definitive answer.
Leave a Reply Cancel reply
Become a CBD Expert!
Subscribe to receive our free guide which will empower you to identify effective, fairly priced CBD products and brands.
As a bonus we will include a coupon good for 20% off your first order!
About Big Sky
We believe that everyone has the potential to benefit from daily use of phytocannabinoid-rich products. Our company was founded with the goal of providing the highest quality, hemp-sourced CBD products on the market and backing these products by superior customer support and supporting education.
Our fairly priced products can be found in our shop and more information about or company and the people behind it can be found on our about page.
CBD isolate is a pure form of the cannabidiol molecule. Learn more about this THC-free, low cost, and versatile substance here.